Creality Ender 3 V2 Full Hotend Kit, 3D Printer Accessories, Assembled Nozzle Kit with Dual Fans and ABS Shell for Ender-3 V2

The media could not be loaded.  Perfect fit replacment has my ender 3 good as new again

Exactly the same

A great replacement I've just upgraded my ender 3 to the ender 3 v2, just remember if your buying this item for your ender 3 make sure you buy the back plate to match 5 out of 5 review

Sadly, after only a month of using 2 of my 3 Ender 3 v2 printers, fan bearings worn out and they became loud and started making bad grinding noise, so I have decided to replace whole hotend and keep the other one as a spare just in case.Even if the instructions are not included, process is straightforward especially if you have previously done a similar job. The whole kit is just as expected, all parts were present and after installation bad noise from fans was eliminated and it is now to see how long will new ones last.Only thing I was confused with was the color of the actual hotend. Stock hotend is red color and the replacement I have received is silver as it can be seen on the image. After contacting Creality and asking if there is any difference they have confirmed that no difference except color are present. So, if you get into same situation this might be helpful.As mentioned this kit has no instructions whatsoever, and It would be nice if it does. It would help with cable management with the board and just show what, how and where should be connected to prevent any mistakes.

This is a full replacement for the hot end on a Creality Ender 3 v2 printer. This includes the actual hot end itself (i.e. heatsink, heater block, throat, nozzle) as well as all the supporting components, so you get;1 x full hot end1 x heater cartridge1 x thermistor1 x ABS mount with shroudAll of this is fully assembled and ready to fit to your Ender 3 v2 printer. All this requires to fit it is to remove the old assembly from the carriage mount, fit this one in its place and then route the cables to attach the heater and thermistor to the printer mainboard in place of the originals.This then gives you a completely new hot end assembly which will solve any problems you may have with the original one, assuming of course the issue is with the hot end and not with the mainboard.As this is an original Creality product you should not have any compatibility problems and at the price this is currently sold it is reasonably good value for money.

No one likes downtime, especially in the middle of a product.I came into my garage to see a half printed object just this week, and realised that the hotend fan had failed on my original unit. My garage often has some dust and particles from woodworking, metal working and other general work. This probably didnt help.Replacing the unit was so easy, easier than I expected. Remove the board cover, undo the cable clips and any cable ties etc, then simply remove from the X carriage and unplug from the board (screw terminals for the heater cartridge and a little bit of hot glue in the way of the thermister connector).Easy peasy, took around 20 minutes start to finish but now I've done it I would say it could be done quicker, easily. I would recommend this for a novice or an expert alike. Really useful spare part for something that can fail easily (Fans, hotend clogs, heater cartridge wires or thermistor can all break easily).

I have a Creality Ender 3 printer and as any 3D printing enthusiast knows, they can be temperamental at times and can regular need some TLC to keep them running smoothly. I have been using it pretty consistently over the last few months and unfortunately it failed on me.This is pretty much a plug and play replacement. while there aren't any instructions included within the package, a quick search on youtube will provide you wit perfectly adequate information to allow you to make the swap. Once I got it on, it has been running nicely with no issues.

the thermistor burnt out and caused temperature issues so had to be replaced. the extruder motor was cracked so had to replace, the build plate was terrible bowed so had to replace

I bought this set to replace my cover hotend. The price for everything included was cheaper than just the hot end. I was very happy to see that the cover mounting holes were reinforced and better than the original. SO I got a new cover and spare parts for the cost of just the cover! Bonus...

Me ha gustado tanto la rapidez de la entrega (llegó 4 días antes de lo previsto), la calidad de la pieza y el embalaje (tienen muchísimo tacto a la hora del embalaje)GraciasUn saludo

Ayant une Ender 3vs depuis maintenant 2 ans en usage semi-pro, on y échappe pas !Ma print ne sortais plus rien apres 3 lit (et encore pas sur un print a 90% du plateau rempli…)J’ai opté pour la version plug & play plus que celle 10€ moins cher ou on se repique sur le support de base, par flemme concrètement.Pas compliqué en suivant le tuto video de la marque.Et… apres 2h de print ca semble plutot ok, la PLA ressort sans souci.Donc produit officiel, et ok. Pour le coup, c’est 5*

Da bei mir das Originale gebrochen war durch einen Fehldruck und Verstopfung im Kühlmechanismus habe ich Ersatz bestellt. Ein bisschen Kabelgefriemel und der Drucker läuft wiederDanach waren die Drucke durch die gut durchdachte Kühlung wieder top.

Replacement hot end. They need to be replaced every year or so, depending on amount of use.At least the parts are not too expensive.