ArdexFeather Finish, Self-Drying, Cement Based Finishing Underlayment Bag 10 Lbs, Grey

Absolutely, love the spa feel every time I take a shower! I couldn't be happier and it was really easy to use, just follow the directions. The one thing I wish was a tad bit different.

Fast delivery

WOW! This was a learning experience / adventure for me!! We live in a 30 year old mobile home. We previously had a "rock" fireplace with a hearth that was raised about 6" off the floor with large stones on top. The mantle was rough cedar, and above the hearth, it was that tacky paper-laminated excuse for panelling. We replaced the panelling with sheetrock; we taped & embedded & textured the walls.We removed the "rock" as well as the entire hearth. I cut and secured the thin hardy board to the wall for the fireplace surround, using screws. I sealed the seams with fiberglass (sheetrock) tape, and I painted them with red sealant. I used this Feather Finish with some cement colorant from Home Depot, and I applied about 7 coats to the front of our fireplace surround. I need to figure out how to add pictures, because it turned out great in our opinion. NO, I had no previous experience with cement, but I have done quite a bit of sheetrock repair and floating of mud in this lovely money pit! (lol) The only reason for so many coats is that colorant makes the cement or feather finish product CHANGE COLORS as it dries, and it dries almost as fast as plaster of paris. You have to work soooo fast, but when you start at one point and go all the way around the fireplace, you end back up at your starting point, right? Since the feather finish mixture is almost dry at this point, and since the colorant changes colors as it dries, you end up with two totally different colors touching each other. It took me a while to figure out how to make this work. I had to start at the top center of the surround and work down from there down both directions! That part was NOT easy. You have to work fast, but this way I would end up at the center bottom of the surround. Again, this is all because of using the colorant. I've been told I need to write my own blog! Probably so!!Since I ran out of this bag mid-project, I learned that you can actually use another product called Henry Feather Finish - product number on the box is 549. ALSO, we had to use a paddle stirring contraption - normally used for stirring paint - or you could use the one for actually stirring together joint compound. The Henry Feather Finish is the same stuff as is in this Ardex bag. They are made by the exact same company -just different packaging. I found the Henry at Home Depot. You just have to search because different territories in the US carry different products and brands. DO KNOW THIS - I found the Henry product - the powder before mixing - to be of a much darker gray that the Ardex. I called the company back and they explained that all cement is that way, that it will vary from batch to batch. Makes perfect sense. I had to then adjust my colorant a bit in order to allow for the Henry feather finish being so much darker.I had originally hoped to have a glass tile fireplace surround, but our tile contractors couldn't come out for weeks! My husband was nervous about us trying to learn to do tile (chicken - haha!). I thought he was gonna stroke over the cement! This feather finish allowed me to rescue our project of making a slimmer profile of our fireplace and giving it a sleek, modern appearance.We now have no hearth, though maybe one day we will create one, but now the surround goes straight down to the floor. We painted the gold colored accents on the screen facing with black paint. That cedar mantle - we took it to a cabinet shop and had them plane it down. I sanded it smooth (didn't take much after going through a commercial planer) and stained it, then put a couple of coats of satin polycrylic on it I think. Totally different room, now. Looks awesome!!!

If this helps one DIYer then it is worth it! I would have loved having this information before starting this project. This was EASY and I finished it in a Saturday afternoon. After reading a dozen tutorials for ardex feather finish on countertops, I was ready to take the plunge and try on my less-risky wood table that needed refinishing anyways. My biggest concern was the amount of dust created by other tutorials involving a ton of sanding between coats and at the end of the process. As someone who has worked a lot with concrete, I just didn’t see why this was necessary! If concrete (cement) is applied properly, it should have a nice smooth surface on its own. Plus, I think the sanding takes away from the natural velvety finish of concrete and ends up looking too forced. Here’s what I did:1) OK here’s where I did sand the table a little bit... you do want to rough up your surface so the cement has something to grab on to. This took me 3 minutes with a sanding sponge.2) I didn’t use a huge trowel or professional float, I just used a 4 inch scraper because that’s what I had on hand, but I think this led to my smooth finish and no sanding needed because I was able to apply the product in thin coats using a lot of pressure since my tool has a thick sturdy blade. Your first coat: don’t fret about it too much. I mixed the feather finish to a peanut butter consistency and spread it on as smoothly as I could, making sure to work as cleanly as I could and not leave anything too rough. I’ve included photos of coats 1,2, and 3 so you can see it gets dramatically better as you go.3) Let it dry until it makes a hard sound when you tap on it. Mix up less for your second coat, (and I hate to say a little bit thinner like pancake batter because I don’t want people to mix it too thin, but this worked for me) using firm pressure I applied a coat as thinly as I could. This really started to smooth things out. Each coat is easier and faster and smoother than the one prior. If you use a thick coat, you will probably have more unevenness that you will have to sand! Think THIN and pressure and keep your blade clean! I wiped off excess cement on dry areas if I felt like I was creating too many trowel lines. In between coats I would let things *almost completely dry* (not too soon or you’ll just add more texture) and then come back with a clean scraper and smooth out any ridges. No sanding needed and the finish looks more natural because I smoothed out any trowel lines this way.3) Repeat until you have the coverage you need. I spent time with a small putty knife obsessing over the edges because I wanted the flat “slab” look and my wood tabletop had rounded edges.4) I lightly lightly sanded the edges or any rough burrs with the sanding block at the very end once I was happy with the finish, creating less than a dime sized pile of dust after I swept it up. The tabletop is buttery smooth and not at all rough, and sealing it will only make it smoother. I really was just in awe of these other people who are blowing horrible cement dust all over their houses!5) I will be sealing after a few days and will update my review to cover any durability issues. My only areas of concern are the corners that I really had to build up with a thicker amount of cement, we will see how these hold together.