Speedy’Z Spring-Lock Cable Pass Port, 2 Inch

Great for helping me make my Ethernet runs into my attic look clean and professional. Super easy to install, and it fits the 2-inch hole perfectly. Makes cable management way more satisfying!

I have a powered cable signal booster in my attic and every time the power blinks off, even momentarily, we would lose TV and internet connections even though the modem and cable boxes are connected to UPS units. I wanted to put that booster on a battery back-up too, but it gets too hot for lead acid batteries in the attic. This provided the perfect solution. I mounted the UPS high on the wall in my garage and used this grommet to route cables through the ceiling. Easy install using a 2.5 inch hole saw. The opening was large enough to accommodate the angled 3 prong plug on the UPS. though it did drag the little rubber insert out at first. Fairly easy to pop back in and I think it looks pretty good.

I used one of these to clean up some cables which need to pass through a wall for a security system. It looks much better than the "hole version 1.0", and I think it should provide better sealing too. However there are gaps in the rubber "seal" which are necessary for the wires to pass though, and leave enough room for bugs to enter. I packed the backside of the pass through with insulation which will help, but also plan to further seal the wire entry point to block the critters too. I think of the available options, these are a pretty good, and simple to install, way to tidy up a wire entry through drywall.

I needed something to cover the hole in the drywall I used to route some cables up and out of my network cabinet. This worked perfectly and was super easy to install. It feels pretty cheap and flimsy, but once it's in, it's in. After reading some of the other reviews I was careful with it and didn't have any issues with the springs or the rubber insert. It popped right into the hole and looks great on the wall.

I love this little "gadget". It does exactly what you need it to do. I cut a 2 1/2" circular hole through my sheet rock wall with my drill (I have the saw attachment) and installed the first one there with the strong spring clips that hold it in place! I put the coax cable and Ethernet connection wires through my bedroom wall and passed them through the living room wall on the other side. I then pulled the wires through and connected them to my Router and Modem, ran them through the second "pass-through" and Voila! A solid, finished look for the wires and the job was done. Now I can stream anything right through the wall! I also used an "L" shaped connector for the cable connection in the bedroom so I could angle the coax cable in any direction I needed. A wonderful self-fix at a fraction of the cost the Internet/Cable company would have charged me! You CAN do this and at little cost as well as little time & effort!

Works great, to run a extension cord from one area to another

This was perfect for my needs with a home audio and TV installation in a newly renovated basement space. The contractor failed to follow wiring diagrams and I was left with no outlets where my stereo and turntable were to go. There was an outlet on the other side of the wall however so all I had to do was drill a 4" hole (with hole saw) on both sides of the wall so I could pass the cords through this portal and they exit on the other side of the wall and directly into a surge protecter and plug. It holds in place with sturdy cleats and looks quite professional. Way better than attempting to hide cords with plastic tubes. I bought a 2nd one for a different location.

I've purchased 3 of these spring-loaded wall grommets/cable pass-thru's and have used them for two different TV installs and also for my home office with my PC. This grommet does what it's designed to do and looks fine but is severely overpriced for what you're getting, which is my primary complaint. ►Deficient rubber/silicone ring material: Aside from my issue with the price, the rubber or silicone material used for the inner part where the cables pass through isn't durable at all. On two of the grommets I've used the inner material has torn completely through. The material can be rotated and is still usable but definitely not rugged at all. ► Installation: Installing this grommet is super easy. I have an adjustable, rotating drywall saw that attaches to my cordless drill and just set that to bore a 2.25" diameter hole. After that just a bit of drywall dust clean up and snap the cable pass-through port into place. ►Pros: + Looks good + Cables pass thru the grommet easily + Simple to install ►Cons: - Expensive - Inner material is cheap and tears easily, especially if you have a lot of cables to run

What a great idea, I like that I can just use a holesaw so its all very neat, and the fact you don't need to use any additional screws or wall mates to secure it is awesome.

With the right size hole saw it takes about 5 minutes to go from idea to finished job. Super easy. The 64mm/2.5inch hole size is just big enough to get power cable ends through (if not too big).

the product is ok but pricey. I thought I would receive a pair but it's only a single item and am therefor a bit disappointed. I woudl go for a product that gives you two items not one