HogueRubber Wraparound Grip for CZ-75, TZ-75, and P-9 Pistols, Black - 75000

I've installed Hogue grips on several pistols I've owned over the years. I have always liked the products. This grip is no different. The quality is good and the fit is tight. The grips fit my hand well and are much more comfortable than the factory ones, in my opinion. They are a little thicker than stock, so work well with my big hands. The biggest difference I noticed was the way it molds in to your hand. Shooting 8" plates at 8 yards, I noticed the position of my hands didn't tend to change from shot to shot. The pistol didn't slip and seemed to be one with my strong hand.I read a few complaints where folks complained these grips didn't fit or required modification. I have the CZ 75B and can see what they meant, but they are wrong. The fit is tight and it's made to fit perfectly. The trick is getting one side in place then stretching the grip around to click in on the other side. The grips are each backed with plastic so they remain rigid, but the center (where the finger grooves are) is only rubber and stretches slightly. There are small extrusions that match up with holes on the frame of the pistol perfectly. Get one side in then stretch the grip a bit as you wrap it around to the other side and it will fit in perfectly. It will seem to be pretty firmly attached even before you apply the screws if you've done it correctly.I've been using these now for over 6 months and probably 2500 rounds. They show no obvious signs of wear.Bottom line: I would recommend these to folks looking for the finger groove style of grips. In fact, I have several times.

Perfect fit on eaa ( tanfoglio) full size SMALL FRAME. Hogue knows their stuff. 5 minutes to install.

Perfect fit on my CZ-75 BD. Feels great in the hand. “Grippy”

I couldn't be any happier with this Hogue grip for my CZ-75B duo-tone. Prior to ordering it, I was a little apprehensive after reading the Amazon reviews mentioning fitment problems, magazine release problems, hand size warnings, etc. So here's my take.I received my package today 2 days early (thanks, Amazon) and the grip probably took all of 60 seconds to install. It didn't interfere at all with my mag release button so it required no trimming. With a trusty flashlight, I could see the interior grip surfaces were fitting perfectly within the frame openings. Thinking I was all done except for the cheering, I attempted to insert an empty magazine. Just as happened to a previous reviewer, it did not want to seat in the frame grip. With a little more force, the mag did install but without the familiar click when fully seated. Upon pushing the mag release, the mag didn't budge and remained completely locked in place. Now, and feeling like the village idiot, I started backing out the two little grip installation screws. After a full reverse turn on each side, the magazine popped right out as it should. Next I tried four empty magazines and each installed and released normally. I didn't feel I had originally installed these screws any tighter than on the CZ factory grips. Everything is working fine and I mention all of this as a heads up for future buyers.As the title of my review states, this grip fit my large hands perfectly. I have long fingers and they fit the finger grooves just right in the grip. I like the feel of the rubber much, much more the the factory grips. The CZ-75 is not a wimpy plastic handgun, it's a heavy, full size, all steel service pistol. IMHO, the Hogue rubber grip is the perfect compliment adding to the already nice balance of this heavyweight.

I am fairly Familiar with Hogue's line of Grips having them on almost every one of my pistols be they revolvers or semiautomatics ! and never a complaint on Hogue Quality ! My only concern was that it would fit my latest pistol Tristar T-120 9MM as no one specifically makes a Grip for Just this pistol ? However The Tristar T-120 9MM pistol which is a Turkish Made Clone of The Jericho 941/ Baby Eagle / baby desert Eagle ? Which is itself a Variant of the CZ-75 Pistol Via Tangfolio and Imi/ Magnum research / Kahr Arms ect... And to make a long story short this Hogue Rubber Grip CZ-75, TZ-75 P-9 Rubber Wraparound with Finger Grooves does indeed fit properly on my Tristar T-120 9MM pistol the original grips were fairly smooth plastic and both not to my liking as much as the hogue's and Imho not as High a Quality as the rest of the Pistol ! the only caveats I have for someone considering these grips is that you will require a lot of pulling and stretching and tugging to get the screw holes to line up and be very careful if you have the cerakoted variation of the Tristar T-120 9MM pistol as I managed to slightly scratch the grip frame with one of the grip screws ! Also once you successfully attach your grips do not over-tighten the grips screws as this will cause your pistols magazine to drag and not eject properly or insert smoothly either ? backing off the screws by a turn or two will solve this problem and yet still secure your grips properly !!! I have read that either soaking your Grips in Hot water for awhile before instillation will allow you to fit them easier ? or you might also try laeving them in the packaging to bake on your dashboard to achieve the same effect ? other than that these grips make a big improvement in the security of the grip and look downright sexy onthe pistol to boot !!!

Used these on my CZ-75 SP-01 tactical. After 2 1/2 years the finger grooves have stretched considerably and I can now feel the finger grooves move when I grip or shoot. Now I'll have to replace these. Avoid.